How To Stain Butcher Block Desk

September 07, 2021 Post a Comment

I didnt bother wiping off the excess since unfinished block will soak up a lot. Allow to dry over 24 hours.

How to Make A Butcher Block Countertop in 2020 Butcher

Then spray undiluted white vinegar, allow it to sit for a few minutes, then wipe it off with a.

How to stain butcher block desk. Start by scraping off any food residue using a metal scraper, running it gently on areas with visible food gunk. Alternatively, you might try using a dye product, either directly on the wood, or as a tint in the clear coat. Its done in just 5 steps .

So the butcher block is resting on that lip and the two drawer units on each side. This helps avoid going too dark in one pass, and reduces blotchiness to some degree. We applied one coat of minwax stain in dark walnut, and then we sealed the wood with a satin polyurethane.

Now i recommend this for any butcher block, particularly if it is not maple. Apply next coat if desired, etc. The secret to the inexpensive butcher block top on this built in desk was a specific piece of wooden board i found when i was at lowes.

Most desks are 6x2.5 (72x30) but choose the size that works best for you up to 39 inches wide without having to join two pieces of butcher block! Choose your wood species and finish. Apply first coat of finish and wipe off excess.

Heres a step by step guide to a diy butcher block desk: Live edge means the characteristics of the outside of the tree are on the edge of the butcher block and will go in and out up to a half of an inch. Give me some feedback if this is incorrect.

How to make inexpensive faux butcher block countertops for a built in desk: Apply mineral spirits to the top and allow to dry. You will use much less mineral oil and feel more secure knowing juice cannot sink deep into the wood grain when you haven't kept up with the oiling.

See more ideas about kitchen remodel, kitchen design, new kitchen. If you stain first then cut, the fresh cuts will require stain causing a possible line where the new stain covers the previous stain. Use a generous amount of finishing product on the underside.

Poly (or any varnish) will enhance the color natural/raw wood, as you can see below with the bottom side of the desk. Its important to seal the surface of the butcher block completely (top, bottom and sides) to prevent bowing/warping from moisture absorption (i. Use the sponge, and scrub the countertop using mild dish soap rinsed in hot water.

Apply first coat of polyurethane and allow to dry for 24 hours. You may have noticed that the shorter side of the desk only has three legs and thought to yourself thats definitely going to fall over! Plan & measure your space.

He also used a few screws and attached the butcher block to the drawer unit from underneath to keep it from slipping. ***find an update on sealing butcher block here, after i lived with it for four years*** while the actual title of this post is how to stain and seal butcher block counters, an alternate title could be how not to stain and seal butcher block counters. because i definitely, definitely did both. Applying product to the bottom of the butcher block will help ward off warping and cracking.

Its finally time to start putting it all together! Sand the wood before staining, then select a wood stain and apply at least 2 coats. Also stain your butcher block if you've had your counters for several years and the current finish is looking worn or faded.

On my journey to find their pre made butcher block tops, i came across something on the entirely opposite end of the store. So imo butcher block should never be sealed it is one of the easiest materials to look after there is an enzyme in the wood that kills bacteria but if you seal it that does not work i have had butcher block for years i oil it when it looks dry, i sand it lightly if it gets stain or burn then oil it the one in this pic is now about 16 yrs old and still looks like new i just oiled it more often near the sinki also dont like them. So dry fit first, then take it back off to stain/sand/stain if you like, though not necessary especially if you dont have the room.

For a desk, skip the oil after the salad bowl finish dries. Apply a thick layer of butcher block conditioner with either a rag or a brush. So for those.read more

Bring the butcher block inside and set it upside down. Lay the top side facing down and measure where you want to place the 4 legs. Wipe down your surface with a dry rag to remove anything left over from sanding.

Let sit for at least 2 hours or according to the brands instructions. (i chose to not oil the bottom side of the desk since it was never going to be seen.) step 2: Carefully measure that each of them are in the exact spot.

More Creative Features from Last Week's Party & Punchbowl